By now, if you are even somewhat involved in RC model aviation, you most likely have heard of the newest technological achievement in our sport. If you are only just now starting to learn about RC flying, then maybe you haven’t yet heard of this new development. No matter your level of RC flying experience, the development of radio systems operating on the 2.4 GHZ frequencies will greatly affect your future RC flying and you should be aware of it.

That is the purpose of this article. Most every magazine, especially the Academy of Model Aeronautic's “Model Aviation” magazine, has printed articles on the subject. Even Sport Aviator has reprinted one of Model Aviation’s 2.4 GHZ articles in the Flight-Tech Section. All the articles hail the new development and explain it in great detail: Maybe in too great of detail.

Not all RC sport pilots, us “common folk” of the sport, want to know the intense technological details of our control systems. We only want to know what we need to know to get the most out of our sport, safely, while also knowing enough to make purchasing decisions.

Our RC control systems have become so advanced that the days of the common pilot building or repairing them is long past. It might be factual to state that our RC control systems went truly Ready-To-Fly in the late 1970’s. For most of us, that was a good thing.

To be honest, few of us common pilots know, or even care to know, a lot of the technical details about our “radios” (what we common pilots call our transmitters and receivers and some even include the batteries in this term.) Instead, we want to turn the “radios” on, have them work continuously for months, then put them away uncharged for centuries and still have them ready to fly, without ever re-charging their 200-year old batteries. We also want our servos (the “motors that move our aircraft’s control surfaces) to weigh less than 7 grams while being able to control the 100 pound rudder on a 66% scale B-36.

But, as much as we would want our radios to work this way, even we radio dummies know that this is not yet possible. We have learned about the care and feeding of our transmitter and flight batteries. (See the three Sport Aviator articles, Those Things We Call Batteries Parts 1 to 3 in the Flight Tech Section). We also learned about servo torque limitations and power drain.

We learned because we had to. If we didn’t learn, we started to lose airplanes. So we learned about battery memory, or lack of it, and their capacities. We learned about computer transmitter programming because knowing enhanced our aircraft’s flying abilities. We learned about field testing our batteries, and about the equipment used for this task, because knowing this information saved our airplanes from those unplanned aircraft-ground interfaces.

All the technical developments made by manufacturers, and especially by the more technically-oriented modelers, have greatly enhanced our sport. Like our sport’s engine “Gurus” who have made modern glow engines, electric motors and gas engines so reliable that common pilots barely need to give them a second thought now, the “Radio Geniuses” have given us reliable systems that almost never fail while performing tasks that would have seemed magical in the 1970’s. Our thanks and appreciation should go to both groups for model aviation would have been a less popular, different sport that was much poorer for their absence.

From their writings and shared knowledge, common pilots have pulled what they needed to know to improve their own flying experience. They took as much or as little as they thought best and incorporated this knowledge into their version of our sport. But now, the Experts have given us something very special that will probably revolutionize the way we fly, not just control, our airplanes. And it is time we common pilots learned what we need to know for our flying and what decisions we need to be making in the next few years.

Let’s look at this development purely from the perspective of the common sport RC pilot. How will it affect our flying and just what do we really need to know about it at this point. Using common, basic terms and targeted just on a true “need to know” basis for the common sport pilot, this is what 2.4 GHz flying will be all about. There will be some basic technical stuff but the parts you really need to know will be identified in bold type.

What is 2.4 GHz?

Photo 1

All of our current aircraft radio control systems operate on one of fifty channels in the 72 MHz (each MHz means the signal’s frequency is one million cycles per second) radio transmission “Band”. “Band” is the range of frequencies that our transmitters use to send signals to our receivers. Our Frequency Band starts at 72.010 MHz (72,010,000 cycles per second) and goes up to 72.990 MHz. Each specific frequency in this band has a 5-number numerical identifier corresponding to its number of cycles per second.

It is somewhat difficult to use the actual 5-number identifier in everyday field use because there are so many of them. Instead, we use two-digit “channel numbers”. A radio system operating on the 72.010 frequency is said to be working on Channel 11. One operating on a frequency of 72.990 MHz is working on Channel 60. The other 48 radio frequencies in the aircraft 72 MHz Band have numbers ranging from Channel 12 to Channel 59 in ascending order.

The new 2.4 GHz (each GHz is one billion cycles per second) radio control systems operate in a Frequency Band that uses far shorter wave lengths. Since both transmitting and receiving antennae have lengths that are related to their frequency band, the 2.4 GHz radio systems have much shorter antenna (photo 1).

At the present time, the transmitter antenna is not removable or collapsible. Some may be rotated to the side but still might not fit into older transmitter cases. This means that many transmitter cases you now have cannot be used with this system. It also means that you will find the transmitter to be slightly “tail heavy” if you use a transmitter neck strap or tray since the heavy metal antenna is replaced by a light “plastic” one. You will also find that the ever-present metal antenna that you have been unconsciously using as a reference point while flying is no longer there.

Photo 2

The receiver antennae are also much shorter in the 2.4 GHz system. Even with 2.4 GHz systems that use dual receivers, the antennae are barely two inches long and usually remain inside the aircraft. The three 2.4 GHz receivers on the right side of photo 2 are just three of the many available.

The AR7000 is the standard sport aircraft receiver designed for use in all sport airplanes flown at any range. The slightly smaller and much lighter AR6200 receiver is a light weight, long range receiver designed for small sport airplanes and helicopters where weight could be a factor. The small AR6100 is for small electrics flown at short ranges.

The two receivers on the left in photo 1 are standard 72MHz items there for comparison. Note the yard-long antennae wrapped around the receivers for storage. Gone are the days of installing yard-long internal tubes to hold the receiver antenna inside the airplane or of stringing the long wire out the side or rear. The very short 2.4 GHz receiver antennae are usually not visible outside the airplane.

Basically and technically, the Frequency Band in which the 2.4 GHz radio system operates is the only true difference. Current systems transmit on 72 MHz and the 2.4 GHz systems transmit on, well they transmit on 2.4 GHz. That’s it, all finished. Problem solved and difference identified. Thank you for reading this article and we hope it helped you better understand the new radio system developments.

“Wait a quantum minute there Frank”, you say? “That just can’t be the whole story”. “There just has to be more to this than a frequency difference” you claim. So you want me to come out with the whole truth and out with it now? OK I will, but you have to get ready to Handle The Whole Truth (sorry for the paraphrase there Jack Nicholson) and some of it may make your eyes glaze over. So hang in there and I will try to explain in common terms what this frequency change really means to us common pilots.

What does the frequency difference really mean?

In all truth, the only real difference IS the frequency difference. But both the Laws of the Universe and the Laws of Man partner to make this simple frequency change into a qualitative difference in the way RC flying will operate in the near future.

First up are the Laws of Man and what they do for us. In its collective wisdom, our government, in the life form of the Federal Communications Commission (FCC), has set rules for all transmitters operating in the 2.4 GHz Band. These rules might also apply to other frequency bands but that is not relative to us here. But one major 2.4 GHz rule, "thou shalt cause no interference", does not apply to our current 72 MHz equipment.

The most common system now operating in the 2.4 GHz band is the portable, not wireless cell, telephone. If you have a portable home telephone with a short antenna, you have already been using the 2.4 GHz Band. (Yes, there are some 5 and 9 GHz portables but the majority still use 2.4 GHz.)

The FCC identified a problem with our portable phone systems almost before their inception. If you are talking on a portable phone and I, your next door neighbor, fire up my portable, it is possible that I could listen in on your conversation or, more likely, interfere with it. So the FCC made this major Law of Man:

For all 2.4 GHz transmitters, every transmitter must first search all the individual 2.4 GHz frequencies in its operating Frequency Band before it ever begins to transmit a signal. No open frequency means no transmitting.

You can hear this Law operating every time you press the talk button on your portable telephone. There is always a delay, usually 1-2 seconds, between pressing the talk button and hearing the dial tone. THAT DELAY is your portable phone searching its operating band BEFORE transmitting a signal to its home base. It searches through its entire frequency range until it finds a single frequency not currently in use in your area. It then, and only then, selects that frequency and transmits to the base set. Therefore, your portable telephone operates on a different frequency each time you use it; within its operating Frequency Band that is.

The 2.4 GHZ radio control systems operate the same way. After you turn on your transmitter, it will search its operating frequency band (2.400-2.4835GHz), find a frequency not in use within its range, select that frequency (sometimes two frequencies but more on that later), and only then actually start to transmit. Some 2.4 GHz transmitters operate on only a few sections of the Frequency Band, others operate over the entire band , hoping from one frequency to another but even this system will not interfere with other manufacturers' 2.4 GHz systems.

This means that no 2.4 GHz transmitter will ever interfere with another 2.4 GHz transmitter that is already controlling an aircraft in flight. No Interference means no “shoot downs”. There will be no need for frequency control systems for 2.4 GHz operation. Of course, a 2.4 GHz system also cannot interfere with 72 MHz operation due to the large frequency difference.

This also means that the old rule of turning on the transmitter before the receiver is now even more important. The new rule is: Turn on the transmitter, wait five seconds and only then turn on the receiver. The reason for this is that some systems need to be told when a change is made to a flaperon system. If you don’t do this, the aileron servos travel to strange territories and sometimes nearly past their operating limits so put the waiting period into your daily operations. Even better, re-bind your receiver to the transmitter after all the setup and trimming flights have been made.

While the Laws of Man actually helped us in this instance, (I leave it up to you whether you find that surprising or not), the Laws of the Universe are not so cooperative. 2.4 GHz waves are very short compared to MHz radio waves. Of course, this makes them “line of sight” only but then, our current 72 MHz band has the same restriction.

However, very short wave lengths mean very short antennae and waves that are easily stopped by conductive surfaces. Unlike our 72 MHZ system with its yard-long receiver antenna, 2.4 GHz systems have 3 inch antennae. This means that, at any given time, some piece of metal (an engine or motor for instance) or electrically conductive item such as a servo wire, a carbon fiber spar or the landing gear will be between the receiver antenna and the transmitter.

When that happens, the short waves are blocked. They are not as good at going “around” objects as are our 72 MHz waves. Nope, they just stop right in their tracks and few reach that really tiny antenna. The result is the airplane continues on its original course until one of the receiver antennae becomes unblocked. Then all is better, if not well.

Photo 3

Recent developments have solved that range problem. Most 2.4 GHz systems use special receivers and antennae systems designed to increase the receiver’s reception abilities. Some use twin receivers. Others use special technology designed for long range use.

Do not be fooled by the length of a 2.4 GHz antenna. Just because the antenna wires are long does not mean it is a long-range receiver. The AR6000 receiver mounted on the airplane in photo 3 has four-inch long antenna but is designed only for short range work. The antennae are not dipole and therefore have weaker reception abilities. The smaller AR6200 receiver is for long-range flight even though its antennae are but 1.5 inches long. These antennae are dipole units meaning they have extra internal surface area for better reception.

The un-mounted AR6200 receiver in photo 3 actually contains two receivers in one and each has its own private antenna. When using twin antenna receivers, always make sure that one antenna is about 90 degrees to the other. That way, at least one antenna is bound to get a signal.

The receiver in photo 4 however, is designed for long range applications. Note that it uses two separate receivers, each of which connects to two dipole antennae. That makes four dipole antennae and two receivers for maximum reception potential.

Photo 4